AT&T StarLAN 10 Manual do Utilizador descarregar pdf

CONFIGURING 3COM 3C507 AND 3C507TP NIC SEPT 11, 1992 [REV. JAN 22, 1993]

LAN SUPPORT TUTORIAL #3 PAGE 1

Configuring 3Com EtherLink 16 NICs LAN Services Tutorial #3

Contents

Introduction ................................................................................................................................................................ 1

Overview of Process ................................................................................................................................................ 3

Figure 1: Overview of Process: Configuring and Installing 3C507 and 3C507TP ................ 4

Configure Card (or TPAU) for 10BASE-T or Draft D .................................................................................. 5

Switch settings for ASP300 ......................................................................................................................... 5

Switch settings for Ungermann-Bass ASP310 and ASP320 TPAUs for use with 3C507

Card ....................................................................................................................................................................... 5

Jumper Settings for 3C507TP..................................................................................................................... 5

Add the 3Com Card to the Server Configuration .................................................................................... 6

Configure 3C507 or 3C507TP ......................................................................................................................... 6

ICA Card Configuration ...................................................................................................................................... 8

Banyan ICA card: Jumper-block settings for various I/O addresses ......................................... 8

For More Information ........................................................................................................................................ 8

Introduction

There are two models of 3Com's 16-bit EtherLink 16 card: the 3C507, and the 3C507TP.

Both cards are 16-bit network interface cards recommended for CNS and ISA PC-based

servers; both cards are supported by VINES 4.11(5), but neither is supported by VINES

5.00(5). (The 32-bit Racal InterLAN card is recommended for EISA-based servers. See the

C&TS Products and Services catalog for details).

The 3C507 contains a BNC connector for coaxial connection to thinnet networks and an AUI

for connection to an external transceiver; the 3C507TP has a built-in 10BASE-T transceiver

with an RJ-45 jack for direct connection to twisted-pair: you'll need a TPAU to connect the

3C507 to TTP (telephone twisted-pair), but you don't for the 3C507TP.

Before installing either card in your server (or workstation), please note these important

considerations:



You must know both the hub type and mode (10BASE-T or Draft D) of the LAN to which

you'll be connecting before the card's network-related settings can be properly made; and



Because of a special addressing scheme used by 3Com, no other card in the server or

workstation can use I/O address 100.

This tutorial provides information about all these issues and includes configuration settings

for the Banyan ICA card, which uses I/O address 100 by default. Refer to Figure 1 or the list

below for an overview of the process. You may wish to leave your existing LAN card in place

in case you encounter problems installing the 3C507; you can remove the existing card at a

later date.

1 2 3 4 5 6 7 8

Resumo do Conteúdo

Página 1 - Introduction

CONFIGURING 3COM 3C507 AND 3C507TP NIC SEPT 11, 1992 [REV. JAN 22, 1993] LAN SUPPORT TUTORIAL #3 PAGE 1 Configuring 3Com EtherLink 16 NICs LAN Serv

Página 2

CONFIGURING 3COM 3C507 AND 3C507TP NIC SEPT 11, 1992 [REV. JAN 22, 1993] LAN SUPPORT TUTORIAL #3 PAGE 2

Página 3 - Overview of Process

CONFIGURING 3COM 3C507 AND 3C507TP NIC SEPT 11, 1992 [REV. JAN 22, 1993] LAN SUPPORT TUTORIAL #3 PAGE 3 Overview of Process Be sure to plan out sett

Página 4

CONFIGURING 3COM 3C507 AND 3C507TP NIC SEPT 11, 1992 [REV. JAN 22, 1993] LAN SUPPORT TUTORIAL #3 PAGE 4 FIGURE 1: OVERVIEW OF PROCESS: CONFIGURING A

Página 5 - JUMPER SETTINGS FOR 3C507TP

CONFIGURING 3COM 3C507 AND 3C507TP NIC SEPT 11, 1992 [REV. JAN 22, 1993] LAN SUPPORT TUTORIAL #3 PAGE 5 Configure Card (or TPAU) for 10BASE-T or Dra

Página 6 - Configure 3C507 or 3C507TP

CONFIGURING 3COM 3C507 AND 3C507TP NIC SEPT 11, 1992 [REV. JAN 22, 1993] LAN SUPPORT TUTORIAL #3 PAGE 6 Add the 3Com Card to the Server Configuratio

Página 7

CONFIGURING 3COM 3C507 AND 3C507TP NIC SEPT 11, 1992 [REV. JAN 22, 1993] LAN SUPPORT TUTORIAL #3 PAGE 7

Página 8 - For More Information

CONFIGURING 3COM 3C507 AND 3C507TP NIC SEPT 11, 1992 [REV. JAN 22, 1993] LAN SUPPORT TUTORIAL #3 PAGE 8 ICA Card Configuration The 3C507 is hardcode

Mais documentos para Redes AT&T StarLAN 10

Para ver o documento AT&T StarLAN 10 Manual de Instruções

AT&T StarLAN 10 Manual de Instruções (456 páginas)

AT&T StarLAN 10 Manual de Instruções (613 páginas)

Comentários a estes Manuais

Sem comentários

AT&T StarLAN 10 Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Redes AT&T StarLAN 10. Configuring 3Com EtherLink 16 Network Interface Cards Manual do Utilizador

Resumo do Conteúdo

Mais documentos para Redes AT&T StarLAN 10

Comentários a estes Manuais

Manuais e produtos relacionados com Redes AT&T StarLAN 10